Straight Razor

The straight razor is intimidating. Powerful. If shaving were a sport, the straight razor would be the chosen blade of the big leagues.

It’s also a luxurious experience. A labored process. There is good reason why we let the professionals—the barbers—wield the blade, while we relax with our eyes closed on their throne.

However, you can give yourself this close of a shave at home, too—if you’re patient enough to learn the process, and confident enough to wield such a top-shelf blade.

You may need a few attempts before doing it perfectly, but like we said: It’s a labored process. Follow guidelines below very closely, and you’ll spare yourself any agony along the way.

Before You Begin

There’s one thing you need to keep in mind here: A straight razor shave takes time. Like, way more time than a cartridge or electric shave—15 minutes, at least.

Most guys should be fine to use a straight razor, even those with sensitive skin. So long as you prepare the skin, work slowly through each step, and condition it after each shave, you shouldn’t experience any serious irritation.

Before picking your blade, you want to consider the blade weight that best suits you. The best way to gauge this is to hold various blades, noting which ones are heaviest. If you end up picking a lighter one, you may need to apply more pressure than a heavier one.

The Process

Straight-razor shaves differ slightly from the otherwise standard guidelines.

1. Preparation

As with any shave, you need to soften the skin and open the pores before using a straight razor. If it’s your first time with a straight razor, then you certainly need to prepare the skin properly to avoid serious burn.

Jump in the hot shower, which will also soften the hairs and allow for a smoother shave. Then apply a pre-shave oil to condition the skin, followed by a transparent shave gel.

2. The Hold

Hold the razor at 30-degree angle from the face. Keep the grip firm, adjusting as necessary for the different parts of the face, like the upper lip and chin. The real key is to pull the skin taut with your other hand and applying gentle pressure with the blade.

This will prevent you from cutting both the face and fingers. The blade is sharp; trust that it’ll do its job.

3. The First Strokes

Pick one side of the face, and start at the sideburn, moving downward. Take the first stroke at a downward slant, from the top of the cheek near the ear. The stroke should be short and even and move without jerks or chopping.

After each short stroke, rinse the blade in hot water and continue. Don’t pull or drag the razor, and reiterates that the skin needs to stay taut.

4. The Chin and Upper Lip

Lift the razor slightly as you approach the chin, and use the middle of the blade. Never begin a fresh stroke on a prominent part of your face, such as the chin or jawbone. Begin a little away from these places, and work over them with steady strokes.

You can approach the two sides of the upper lip as you would the cheeks, with short, steady strokes. Pull the opposite side of the lip taut, however, to flatten the skin.

5. The Lower Lip and Neck

Practice adjusting your mouth so that the skin of your lower lip is widened and tightened. Take the first strokes from the corner of your mouth, across the skin to the center of your chin. You can then shave any remaining hairs with short upward strokes; start from the top of the chin, and let the razor follow the contours beneath your lips.

6. Repeat

It’s likely you will have to do a second pass, spot checking for any missed patches. Shave against or across the grain on the face during this second round. But, remember to re-lather your face with shaving cream or gel, after a hot splash of water on the skin.

7. Moisturize

Immediately after shaving, splash some cold water on the skin to tighten the pores. Apply a post-shave balm or moisturizer to the skin, patting it in instead of massaging it. Any rubbing might cause irritation.

8. Storage

Blade storage is serious business. Rinse the blade and wipe it with a soft cloth; this will rid of any debris and moisture. Store it away from any moisture—some place where the steam of the shower won’t get to it.

If you need to store it for a long period, then buy a blade oil. Rub the oil over the blade before putting it away. This prevents any moisture in the air from rusting the blade. If your blade gets rusty, do not re-use it. Replace it.


Please enter your comment!
Please enter your name here